When ordering assemblies, specify “P” pin dia. and “D” distance from bearing point to fitting. “P” should be at least five (5) times the cable diameter for guaranteed breaking strength and “D” should be at least 2.5 times “P”.
GENERAL NOTES:
1. Although the stainless steel loop sleeves are available loose, they are usually factory applied.
2. Wherever possible, thimbles should be used with loop sleeves to protect the cable.
3. Specify pin “P” diameter.
Strength–when crimped over bare cable, standard length loop sleeves generate full breaking strength of cable. For shorter loop sleeves with suffix 1 or sleeves swaged over plastic, consult factory. Stainless steel sleeves generate a minimum of 85% of cable rated breaking strength.
Depending on size and material, loop sleeves may have round, oval or figure eight shape. Call factory for details, if required.
Copper may be substituted for brass, depending on availability.
Part No.
For Cable
Dia.
Material
Ls Ref.
after Swage
Use Tool &
Cavity No.
7000B
7000S (S1)
.006 - .014
Brass
Stainless Steel
.19
.25 (.06)
Pliers
Factory Applied
7020B (B1)
7020S
.016 - .022
Brass
Stainless Steel
.28 (.11)
.25
T185-A
Factory Applied
7025B
7025S
.023 - .026
Brass
Stainless Steel
.28
.28
T185-A
Factory Applied
7030C (C1)
7030S
.027 - .038
Zinc-Plated Copper
Stainless Steel
.28 (.16)
.28
T185-D
Factory Applied
7047C (C1)
7047S (S1)
.039 - .054
Zinc-Plated Copper
Stainless Steel
.44 (.18)
.38 (.18)
T185-B or T188-1
Factory Applied
7062A
7062C (C1)
7062S
1/16
Aluminum
Zinc-Plated Copper
Stainless Steel
.46
.42 (.32)
.45
T185-C or T188-2
T185-C or T188-2
T188-1
7092A
7092C
7092S
3/32
Aluminum
Zinc-Plated Copper
Stainless Steel
.63
.50
.44
T188-3
T188-3
51-C-887 or T188-2
7125A
7125C
7125S
1/8
Aluminum
Zinc-Plated Copper
Stainless Steel
.81
.75
.42
T188-4
T188-4
51-G-887 or T188-3
7156A
7156C
7156S
5/32
Aluminum
Zinc-Plated Copper
Stainless Steel
1.03
.88
.78
T188-5
T188-5
51-M-850 or T188-4
7187A (A1)
7187C
7187S
3/16
Aluminum
Zinc-Plated Copper
Stainless Steel
1.19 (.55)
1.25
1.10
T188-6
T188-6
51-P-850 or T188-5
7218A
7218C
7/32
Aluminum
Zinc-Plated Copper
1.50
1.06
Factory Applied
51-F2-850
7250A
7250C
7250S
1/4
Aluminum
Zinc-Plated Copper
Stainless Steel
1.63
1.50
1.50
3-F6-950
3-F6-950
Factory Applied
7312A (A1)
7312C
5/16
Aluminum
Zinc-Plated Copper
1.70 (.86)
1.38
Factory
Applied Only
7375A (A1)
7375C
3/8
Aluminum
Zinc-Plated Copper
2.38 (.95)
1.63
Factory
applied Only
NOTE: For large diameter cable sleeves, different lengths or finishes, consult factory. Loop sleeves per MS51844 also available, consult factory.
GENERAL NOTES:
To obtain proper breaking strength with T188 tool, crimp once, rotate stop sleeve 30° and crimp again or allow factory to swage onto cable. Unless specified, cable will protrude beyond crimped stop sleeve or cable can be ground flush.
Also available in aluminum and other alloys, consult factory.
Stop Sleeves
Part No.
Ref. Old
Part No.
For Cable
Dia.
Ls Ref. after
Crimped
Typical
Holding Strength Lbs.
Tool &
Groove Cavity
8030C
803C
1/32
.22
110
T185-D
8047C
804C
3/64
.28
240
T188-1
8062C
805C
1/16
.30
325
T188-2
8092C1
806C
3/32
.38
400
T188-3
8125C
807C
1/8
.38
900
T188-3
8156C
808C
5/32
.41
1200
T188-4
8187C
809C
3/16
.41
1600
T188-4
8218C
810C
7/32
.75
2500
51-MJ
8250C
811C
1/4
.82
3500
3-F6-950
NOTE: Std. material is copper. 12093 cable holds 250 lbs. min. when using 8092C
Loop Crimps
Loop crimps are factory applied splices, which are very economical and hold approximately 50% of cable breaking strength dependent on cable size and type used. Not sold in bulk.
