Sava Industries, Inc. - Prototype Assemblies & Kit Package

Cable Fittings
(PDF 1.1 MB)

Product Line »
Prototype Assemblies & Kit Package

Prototype Assemblies

Make your own prototype cable assemblies, lanyards, control cabling, etc. Use the finest, most flexible, most durable material–SAVA’S Miniature Cable–a multiplicity of fine STAINLESS STEEL wires, internally lubricated and coated with a tough abrasion-resistant nylon. When your design is completed, inquire with SAVA about production quantities.

This package consists of:
Precision Crimping Tool No. T185
2 choices of the following 20 cable sizes
4 choices (15 pcs. ea.) of the following fittings

Kit Package – MK 48

Cable Part No.	Size of Spool or Coil	Outside Diameter (Including Coating)	Construction	Breaking Strength	Loop/ Sleeve	Ball End Plug	Threaded Plug2
2009SN	25´	.014	3x7	10	7000B	401B1 or 403B1	455B0500
2012SN	25´	.019	3x7	18	7020B	401B1 or 403B1	455B0500
2014SN	25´	.019	7x7	26	7020B	401B1 or 403B1	455B0500
2018SN	25´	.024	7x7	40	7025B	401B1 or 403B1	455B0500
2024SN	10´	.030	7x19	70	7030C	403B2 or 405B2	455B0500 or 460B0500
2027SN	25´	.034	7x7	90	7030C	403B2 or 405B2	455B0500 or 460B0500
2031SN	25´	.037	7x7	120	7030C	403B2 or 405B2	455B0500 or 460B0500
2032SN	10´	.037	7x19	120	7030C	403B2 or 405B2	455B0500 or 460B0500
2036N	25´	.044	7x7	160	7047C	403B3 o 405B3	455B0500 or 460B0500
2037SN	10´	.046	7x19	160	7047C	403B3 or 405B3	455B0500 or 460B0500
2038SN	10´	.046	49+(8x19)	160	7047C	403B3 or 405B3	455B0500 or 460B0500
2047SN	10´	.052	7x49	170	7047C	405B4 or 410B2	465B0500
2048	15´	.046	7x7	270	7047C	405B3 or 410B1	465B0500
2048SN2	15´	.062	7x7	270	7062A	405B31 or 410B1¹	465B0500¹
2050SN2	15´	.062	7x19	270	7062A	405B31 or 410B1¹	465B0500¹
2054SN2	10´	.062	7x49	250	7062A	405B41 or 410B2¹	465B0500¹
2064	15´	.062	7x7	480	7062A	405B4 or 410B2	465B0500
2064SN3	15´	.093	7x7	480	7062A¹	405B41 or 410B2¹	465B0500¹
2065	15´	.062	7x19	480	7062A	405B4 or 410B2	465B0500
2065SN3	15´	.093	7x19	480	7062A¹	405B41 or 410B2¹	465B0500¹

NOTE: Tool No. T185 is designed to give full cable strength for the loop sleeves. The ball end plugs and the threaded plugs, crimped over the nylon, will give approximately 50% of the rated breaking strength of the cable when properly applied. All above fittings, when factory applied, will give full rated strength of the cable. To get maximum crimping bond, strip nylon from cable. The T185 is designed for prototype or short-run applications by attaching fittings to cables and is to be used only on brass and copper fittings. We recommend that all assemblies made with the T185 be tested for strength before use.